Exactly. That is where I am going to start. Hopefull I can get a blade that will slice cleanly enough for me that my laminations can go from the bandsaw directly to glueup. I found this: http://www.tools-for-woodworking.com/product.asp?0=294&1=295&3=1294 It is from Highland Hardware and is called their Wood Slicer bandsaw blade. It is a Super Sharp Thin-Kerf Precision Resawing Blade. It is specifically made for cutting veneers (not that I haven't heard that before!). I would like to turn 12 mm of nice maple into a 6 mm thick cap of 1 mm laminations. We shall see. Terry Farrell ----- Original Message ----- From: "Greg Newell" <gnewell@ameritech.net> To: "Pianotech" <pianotech@ptg.org> Sent: Saturday, February 15, 2003 11:51 PM Subject: Re: Thickness Planer > > Terry, > I think if I were going to do this with a bandsaw cut only I would > be looking into different blades for the saw. I would definitely look for > more teeth per inch and perhaps a skip tooth blade as well to attempt at a > smoother cut. While our saws cut pretty much anything we throw at them my > experience so far is not one of terribly smooth cuts. More of an industrial > machine I guess. > > Greg > > > > At 11:05 PM 2/15/2003, you wrote: > > >Thank you Greg. What a wonderful idea. I'm sure I could make that work > >somehow or other - at least worth a try. Some of my thinking on bridge cap > >laminations also runs toward: how smooth a cut do we need? What about just > >a nice smooth cut straight from the band saw? Something the equivilent of > >a 60 to 80 grit sanding job? > > > >I cut some sample 1 mm laminations with an inappropriate band saw blade > >(really coarse) and 9 laminations clamped together totalled 12 mm thick! I > >guess right around 25% air! Nope, gotta get a smoother surface than that! > > > >Terry Farrell > > > >----- Original Message ----- > >From: "Greg Newell" <gnewell@ameritech.net> > >To: "Pianotech" <pianotech@ptg.org> > >Sent: Saturday, February 15, 2003 10:41 PM > >Subject: Re: Thickness Planer > > > > > > > I don't know how feasible this would be but you could attach the piece you > > > want to plane piggy back style to a straight flat piece with double sided > > > tape. Run them through together and then separate and you should have what > > > you want. > > > > > > Greg > > > > > > > > > At 09:30 PM 2/15/2003, you wrote: > > > > > > >Ron Nossaman stated that he thickness planes hard maple to 1.5 to 2 mm > > > >thick laminations. I have a 12-1/2 inch DeWald thickness planer, but it > > > >seems the thinnest it will plane down to is about 1/8 inch, or about 3 > > mm. > > > >What planer goes down to 1.5 mm. Or are modifications possible to > > > >accomplish this? > > > > > > > >Terry Farrell > > > > > > > >_______________________________________________ > > > >pianotech list info: https://www.moypiano.com/resources/#archives > > > > > > Greg Newell > > > mailto:gnewell@ameritech.net > > > > > > > > >-------------------------------------------------------------------------------- > > > > > > > _______________________________________________ > > > pianotech list info: https://www.moypiano.com/resources/#archives > > > > >_______________________________________________ > >pianotech list info: https://www.moypiano.com/resources/#archives > > Greg Newell > mailto:gnewell@ameritech.net > -------------------------------------------------------------------------------- > _______________________________________________ > pianotech list info: https://www.moypiano.com/resources/#archives >
This PTG archive page provided courtesy of Moy Piano Service, LLC