Thanks Terry, we have a JoAnn Fabrics Store in the mall which always has all of the gagets. Regards, Gordon On 25 Jul 2002 at 16:00, Farrell wrote: > Go to Wal Mart or any fabric store and get the little fabric cutting razor blade wheels. They come in a variety of sizes and several manufacturers. They are absolutely amazing. Cut any angle cleanly. Great for key bushings and dampers also. > > Terry Farrell > > ----- Original Message ----- > From: "Gordon Holley" <gholley@hi-techhousing.com> > To: <pianotech@ptg.org> > Sent: Thursday, July 25, 2002 3:20 PM > Subject: Re: Understring Felt and Stringing Felt (Braid) > > > > Thank you Newton. Now to find the correct blade or knife to cut the > > angle on the felt. I assume that Schaff would have the recommended > > knife?. Regards, Gordon > > On 25 Jul 2002 at 12:42, Newton Hunt wrote: > > > > > Re: bass felt. You will need to know how much bearing you have. If you > > > have extra bearing then you can replace this felt. Using a rubber > > > mallet you can "hammer" the felt over the pins. If you are low on > > > bearing leave this felt out. > > > > > > Weave the tail ends to quiet them. > > > > > > Felt between pins and bear bar is optional but I would put it in to > > > quiet the segments. Use felt, rather dense like bachcheck felt that is > > > no more than 1 mm higher than the bar. But the felt at a angle _/ so it > > > snuggles up to the bar and the cut provides relief so there is no abrupt > > > change in height. > > > > > > Newton > > > > > > Gordon Holley wrote: > > > > > > > > List. I'm rebuilding a Starr 5' Grand and have questions regarding > > > > the felt application that WAS used in this piano in 1936 and should I > > > > do anything different today. I'm having Danny at G.C. Piano, > > > > Scarsborough, Ont., make new bass strings and is rescaling the tenor > > > > and treble. The strings should be in hand in about a week so I've > > > > got time to order additional felt if needed. > > > > Question 1. There was no stringing felt, interwoven, used in the non- > > > > speaking lengths of the bass strings between the bass bridge and the > > > > hitch pins. However, there was understring felt, with holes punched > > > > in for the hitch pins, the full length of the bass mono and bi-chord > > > > strings. Should I now use stringing felt in this position? > > > > Queston 2. There was no understring felt on the tuning pin side of > > > > the front bearing bar in the non-speaking length, between the bar and > > > > the pins. I've seen other grands with this application where the > > > > felt, approx. 1/2" width, was snugged up to the side of the bearing > > > > bar. Again should I now use a felt here in this position. > > > > Would these two felt applications, if felt was now inserted, have an > > > > adverse effect on the sound. > > > > I must admit, this is my first attempt of this magnitude, and I'm > > > > learning. I've refinished the soundboard, have new hammers and > > > > shanks in hand to install, new pin and bushings to install, new > > > > damper wire guide rail bushings do do yet, refinished the plate with > > > > Steinway Gold and topcoat in on the way, new pedal rods, plate bolts > > > > polished with a coat of lacquer applied. > > > > Many list members have contributed to the steps with suggestions, > > > > hints, and material sources, and many have said on the list, "If you > > > > can't find the answer, just ask and we'll help". Well, I'm asking > > > > for some additional help. And hopefully, being a new born of 18 > > > > months, I won't get "Boo'd out of the class" for asking, what the > > > > more experienced ptg members would consider as, such an elemental > > > > question. > > > > And, this is addressed to other "newbees" out there, "Stay the > > > > course, don't be afraid to ask questions, and study and practice over > > > > and over 'till you get it right". > > > > I thank you all for your contributions in advance. Respectfully, > > > > Gordon Holley, Goshen, Indiana. > > > >
This PTG archive page provided courtesy of Moy Piano Service, LLC