If epoxy penetrates cracks just as well as CA does, then why don't we use it to treat loose tuning pins? Dean Dean W May (812) 235-5272 voice and text PianoRebuilders.com (888) DEAN-MAY Terre Haute IN 47802 -----Original Message----- From: pianotech-bounces at ptg.org [mailto:pianotech-bounces at ptg.org] On Behalf Of Joseph Garrett Sent: Monday, November 05, 2012 9:15 PM To: Terry Farrell; pianotech at ptg.org Subject: Re: [pianotech] Epoxy Terry, As I said, It was a while ago, and it could be as you say. I may have read it or interpreted it wrong. I think I was wrong back in the 70's, but can't remember the specifics on that either.<G> As for System Three epoxies, I did not say it would cure slower at higher temps. I think what I said was that heat didn't seem to make it cure faster, as some epoxies do and some have assumed pertains to ALL epoxies.<G> At one time or another, I think I've used most of the major epoxies and a few some haven't even seen or heard of.<G> It's a huge part of my bag of trix.<G> It is far more versital,(sp?) than CA is, imo. Joe > [Original Message] > From: Terry Farrell <mfarrel2 at tampabay.rr.com> > To: <joegarrett at earthlink.net>; <pianotech at ptg.org> > Date: 11/5/2012 5:59:40 PM > Subject: Re: [pianotech] Epoxy > > Hi Joe, > > I can't comment specifically on the epoxy you saw in the magazine because you don't have the manufacturer, however all the epoxies I have read about that are designed for use in cooler weather simply have the feature that they will harden at cooler temperatures - they will still harden faster at higher temperatures. > > I doubt that the article said that the epoxy would cure faster in cold weather than warm - likely it simple pointed out that it WOULD cure in cool weather. > > But if I am wrong (it happened once before in 1962), please provide specifics so that I can expand my knowledge. > > Here's a link to System Three Cold Cure epoxy: http://www.systemthree.com/reslibrary/tds/Cold-Cure_TDS.pdf It states that it will cure down to 35 degrees F - doesn't say anything about curing slower at higher temps. > > Thanks. > > Terry Farrell > > On Nov 5, 2012, at 12:48 PM, Joseph Garrett wrote: > > > Mike, > > I read an article in a Sailing magazine that said there were a few epoxies > > that were designed for colder temps, in making emergency repairs to a boat. > > Since it's been a while and I didn't consider it pertinent to what we do, I > > cannot recall the specific brand or group of epoxies it was. Suffice it to > > say, the article did state that some would set faster in cold. At the time > > I thought that was interesting, since I was always under the impression > > that the heat generated by the chemical processes of epoxies, was the > > determining factor. I wish I could be more specific in that regard. > > Best, > > Joe > > > > > >> [Original Message] > >> From: Mike Spalding <mike.spalding1 at frontier.com> > >> To: <joegarrett at earthlink.net>; <pianotech at ptg.org> > >> Date: 11/5/2012 9:11:26 AM > >> Subject: Re: [pianotech] Epoxy > >> > >> Joe, > >> For our edification, can you name one epoxy that cures faster cold than > >> hot? This cut-n-paste from the West Systems "how to use" page > >> summarizes the behavior of every epoxy I've ever used: > >> > >> > >> > >> */Figure 1---/All resin/hardener combinations go through the > >> same phases of cure. All combinations cure faster at warmer > >> temperatures and cure slower at cooler temperatures. > >> * > >> cheers, > >> > >> Mike ----- No virus found in this message. Checked by AVG - www.avg.com Version: 2012.0.2221 / Virus Database: 2441/5375 - Release Date: 11/05/12
This PTG archive page provided courtesy of Moy Piano Service, LLC