Thanks everyone for your input on the Ernst Kap grand. Ron Ochs Masterwork Pianos (541) 273-1663 ron at masterworkpianos.com ----- Original Message ---- From: "pianotech-request at ptg.org" <pianotech-request at ptg.org> To: pianotech at ptg.org Sent: Friday, June 27, 2008 11:00:29 AM Subject: Pianotech Digest, Vol 1300, Issue 134 Send Pianotech mailing list submissions to pianotech at ptg.org To subscribe or unsubscribe via the World Wide Web, visit https://www.moypiano.com/resources/#archives or, via email, send a message with subject or body 'help' to pianotech-request at ptg.org You can reach the person managing the list at pianotech-owner at ptg.org When replying, please edit your Subject line so it is more specific than "Re: Contents of Pianotech digest..." Today's Topics: 1. Re: Ernst Kaps grand (andr? oorebeek) -----Inline Message Follows----- In spite of the name 'Pantzer Platte', most of the Ernst Kaps piano's I've come across had broken iron frames. friendly greetings from André Oorebeek On Jun 27, 2008, at 1:35 AM, Jurgen Goering wrote: Any large, heavy plate is sometimes referred to as "Panzer Platte" in German. If it were cast out of a higher grade, more expensive steel, it would surely be designated "Stahl Platte", to set it apart from a "Guss Platte" (cast iron plate). So much for the language and terminology. But who knows exactly what Kaps' plate were made of? One definite answer would be the results of a lab test of a piece of the plate... Jurgen Goering On Jun 26, 2008, at 15:08, John Delacour wrote: At 11:40 -0700 26/6/08, Jurgen Goering wrote: ..."Panzer", by the way means nothing more than "strong, protective plate" aka "armored". (Think turtles and bank vaults.) Perhaps Kaps used that term in connection with full piano plates as opposed to 3/4 plates? It could also be that the frames were made of cast steel rather than cast iron. About the turn of the century Broadwood's grand frames were of cast steel, including, I think, the frame for the barless grands. Such a frame would, I think, be extremely tough and very expensive to produce compared with the usual grey iron casting. JD _______________________________________________ Pianotech list info https://www.moypiano.com/resources/#archives In spite of the name 'Pantzer Platte', most of the Ernst Kaps piano's I've come across had broken iron frames. friendly greetings from André Oorebeek On Jun 27, 2008, at 1:35 AM, Jurgen Goering wrote: Any large, heavy plate is sometimes referred to as "Panzer Platte" in German. If it were cast out of a higher grade, more expensive steel, it would surely be designated "Stahl Platte", to set it apart from a "Guss Platte" (cast iron plate). So much for the language and terminology. But who knows exactly what Kaps' plate were made of? One definite answer would be the results of a lab test of a piece of the plate... Jurgen Goering On Jun 26, 2008, at 15:08, John Delacour wrote: At 11:40 -0700 26/6/08, Jurgen Goering wrote: ..."Panzer", by the way means nothing more than "strong, protective plate" aka "armored". (Think turtles and bank vaults.) Perhaps Kaps used that term in connection with full piano plates as opposed to 3/4 plates? It could also be that the frames were made of cast steel rather than cast iron. About the turn of the century Broadwood's grand frames were of cast steel, including, I think, the frame for the barless grands. Such a frame would, I think, be extremely tough and very expensive to produce compared with the usual grey iron casting. JD -------------- next part -------------- An HTML attachment was scrubbed... URL: https://www.moypiano.com/ptg/pianotech.php/attachments/20080627/abc3ae3a/attachment.html
This PTG archive page provided courtesy of Moy Piano Service, LLC