I did try the brush thing, but I did not have much success. The brush I had was a twisted wire type of shaft, and the handle, if it had one, was not a secure one. I don't remember if it had one, it was a long time ago. Anyway, I twisted it and got the brush in the pin hole, but I couldn't get it out, without a lot of trouble. Reason being the bristles were pointing out of the hole, and dug in, when I tried to remove it. Almost like some animals teeth, the grab, and you have to rip to get free. If it originally had a handle, it pulled off, when trying to remove the brush. It was the one from Pianotek TPB-1. I never did get it to work right. Mind you, my methodology, might have been wrong. But how can I be wrong, you push it in, and then pull out. Except, it wouldn't come out. John M. Ross Windsor, Nova Scotia, Canada jrpiano@win.eastlink.ca ----- Original Message ----- From: "gordon stelter" <lclgcnp@yahoo.com> To: "Pianotech" <pianotech@ptg.org> Sent: Thursday, August 25, 2005 7:52 PM Subject: Re: To Ream or Not to Ream? > Like I said ( and nobody responded ): How is this > superior to just running a wire brush in and out a few > times, to knock off glaze, and roughen the wood a bit > ? > Thump > > > --- John Ross <jrpiano@win.eastlink.ca> wrote: > >> I wouldn't recommend using a drill. >> I use a bit holding attachment that fits into a >> power screwdriver/screwdriver, and just turn by >> hand. >> A drill is hard to control, and ends up being too >> aggressive. >> That is my take. >> Others may have a method that they find works >> better. >> I would like to hear of any suggestions, regarding >> the use of the fluted reamers, for use on pinblocks. >> John M. Ross >> Windsor, Nova Scotia, Canada >> jrpiano@win.eastlink.ca >> ----- Original Message ----- >> From: Pierre Gevaert >> To: Pianotech >> Sent: Thursday, August 25, 2005 1:00 PM >> Subject: Re: To Ream or Not to Ream? >> >> >> Hi, >> >> Thanks for the reply concerning the fluted >> reamers. >> Concerning these reamers do some of you have some >> experience to share? I was wondering what kind of >> drill should be used and what would be a good >> feed-rate. >> >> Thanks, >> >> Pierre >> ----- Original Message ----- >> From: John Ross >> To: Pianotech >> Sent: Wednesday, August 24, 2005 9:07 PM >> Subject: Re: To Ream or Not to Ream? >> >> >> I got my fluted reamers from Pianotek. They have >> six sizes from .266" to.295", they are 6" long and >> the flute is 1 1/2". >> I do find them better, but you have to take it >> slow. >> John M. Ross >> Windsor, Nova Scotia, Canada >> jrpiano@win.eastlink.ca >> ----- Original Message ----- >> From: Pierre Gevaert >> To: Pianotech >> Sent: Wednesday, August 24, 2005 2:02 PM >> Subject: Re: To Ream or Not to Ream? >> >> >> Hi, >> >> And what about those fluted reamers mentionned >> in the Reblitz? I've tried to find these for a long >> time now but without succes. As I never heared >> anyone else speaking about these I suppose it's not >> that good to use? >> >> >> Pierre Gevaert >> >> Belgium >> ----- Original Message ----- >> From: John Ross >> To: pianotech >> Sent: Tuesday, August 23, 2005 9:24 PM >> Subject: To Ream or Not to Ream? >> >> >> I normally used to ream, before repining. >> However on this latest piano, the pins were >> tight on removal. Sorry, I forgot to take a torque >> measurement. >> I normally just go up one size, unless they >> are really loose. >> I am tempted to just go up the one size, and >> not ream. I do use pin driving fluid. >> >> I would like to be reminded of the pros, and >> cons of each procedure. >> >> It is a good quality upright, a Heintzman, >> with what they call an Agraffe Bridge, patented in >> 1895. It is the one with the three holes drilled >> through the plate, aligning the strings. >> >> It had no 1/2 sizes of strings. I am adding >> a few that seem to improve the inharmonicity, >> according to PSCALE. >> >> John M. Ross >> Windsor, Nova Scotia, Canada >> jrpiano@win.eastlink.ca >> > > > __________________________________________________ > Do You Yahoo!? > Tired of spam? Yahoo! Mail has the best spam protection around > http://mail.yahoo.com > _______________________________________________ > pianotech list info: https://www.moypiano.com/resources/#archives >
This PTG archive page provided courtesy of Moy Piano Service, LLC