Mvc-020s.jpg

[Joe And Penny Goss]

Hi Alan,
Sorry I shuld not have gotten sidetracked onto another tool when talking
about the fitting block. That is most likely where I lost you.
The fitting block is used as a tool for very fine removal of felt at any
string to hammer inpact point. There are four sanding surfaces.
1. to remove felt from one string center only
2. to remove felt from the outside string only ( left/right by turning the
block arround )
3. to remove felt from any two string surfaces ( left/right as above )
4. all three string contact points ( seldom used ) if you need to start over
or the hammer shows that the outside is blocking heavier than the center.
Hope this makes it a tad clearer. <G>
Joe Goss
imatunr@srvinet.com
www.mothergoosetools.com
----- Original Message -----
From: "Alan R. Barnard" <mathstar@salemnet.com>
To: "Pianotech" <pianotech@ptg.org>
Sent: Saturday, September 28, 2002 8:55 PM
Subject: Re: Mvc-020s.jpg


> I may be stupid or just really tired but I don't get it. I need more info
> ... you've only tweaked my interest.
>
> Alan Barnard
> Suspenseful in Salem, MO
>
> ----- Original Message -----
> From: "Joe And Penny Goss" <imatunr@srvinet.com>
> To: "Pianotech" <pianotech@ptg.org>
> Sent: Saturday, September 28, 2002 9:05 PM
> Subject: Re: Mvc-020s.jpg
>
>
> > Hi Gordon,
> > This tool is used for final mating of string and hammer after the
strings
> > have been leveled in a grand and the hammers reshaped.When doing work on
> an
> > upright I will try to mate the hammer to the string first by seating the
> > string with my brass seating rod and if that does not work I will use
the
> > fitting block. Between the two one can eliminate a lot of wierd noise in
> the
> > low tenor notes of an upright.
> > Joe Goss
> > imatunr@srvinet.com
> > www.mothergoosetools.com
> > ----- Original Message -----
> > From: "gordon stelter" <lclgcnp@yahoo.com>
> > To: "Pianotech" <pianotech@ptg.org>
> > Sent: Saturday, September 28, 2002 7:08 PM
> > Subject: Re: Mvc-020s.jpg
> >
> >
> > > What is this? Looks very elegant.
> > >      Gordon Stelter
> > >
> > > --- Joe And Penny Goss <imatunr@srvinet.com> wrote:
> > > > Hi all,
> > > > Only open if you want to see the new design of the
> > > > fitting block. The new design is now on my web site
> > > > but is available in quanities now.
> > > >
> > > >  Mvc-020s.jpg
> > > >
> > >
> > > > ATTACHMENT part 2 image/jpeg name=MVC-020S.JPG
> > > > _______________________________________________
> > > > pianotech list info:
> > > > https://www.moypiano.com/resources/#archives
> > > >
> > >
> > >
> > > __________________________________________________
> > > Do you Yahoo!?
> > > New DSL Internet Access from SBC & Yahoo!
> > > http://sbc.yahoo.com
> > > _______________________________________________
> > > pianotech list info: https://www.moypiano.com/resources/#archives
> >
> > _______________________________________________
> > pianotech list info: https://www.moypiano.com/resources/#archives
>
> _______________________________________________
> pianotech list info: https://www.moypiano.com/resources/#archives