Pinblock too low

Mike and Jane Spalding mjbkspal@execpc.com
Fri, 13 Sep 2002 07:10:40 -0500


Isaac,

Good idea - I'll check the glide bolts.  It goes in and out with equal difficulty.  I'm trying to imagine how hard it was to push in the first time, before the drop screws had gouged out the grooves in the pinblock.  Flat wood rails, not tubular.

Mike

----- Original Message ----- 
From: Isaac OLEG <oleg-i@wanadoo.fr>
To: Pianotech <pianotech@ptg.org>
Sent: Thursday, September 12, 2002 10:08 PM
Subject: RE: Pinblock too low


> Un screw the glide bolts  !
> 
> How do you believe the action could go inside and not outside ?
> 
> Some sign of stripped rail on tubular frames.
> 
> 
> Regards
> 
> IO
> 
> > -----Message d'origine-----
> > De : pianotech-bounces@ptg.org 
> > [mailto:pianotech-bounces@ptg.org]De la
> > part de Greg Newell
> > Envoye : vendredi 13 septembre 2002 03:22
> > A : Mike and Jane Spalding; Pianotech
> > Objet : Re: Pinblock too low
> > 
> > 
> > Mike,
> >          I encountered something exactly like this after I 
> > had sent my 
> > customers piano to a rebuilder and it came back as you 
> > described. I told 
> > the customer it should go back but they refused as it had 
> > already been at 
> > the rebuilders 2 months longer than expected. Since I had 
> > to resolve the 
> > problem myself I went at the underside of the pin block 
> > with a (initially) 
> > sharp chisel. I peeled off two layers cursing under my 
> > breath the whole 
> > time and hit many a low tuning pin in the process. When all 
> > was said and 
> > done it regulated fine and is a fine instrument today but 
> > Oh what an ordeal 
> > that was! Not one of my proudest moments sending it to that 
> > fellow. FWIW
> > 
> > Greg newell
> > 
> > 
> > At 06:50 PM 9/12/2002, you wrote:
> > 
> > >List,
> > >
> > >Today I was asked to examine a "rebuilt" piano and figure 
> > out why it plays 
> > >so poorly.  Knabe small grand from mid-1920's.  It was 
> > obvious just 
> > >sitting at the kyboard an playing a little, that the 
> > damper timing was way 
> > >uneven, and drop was way low.  Thought the solution would 
> > be failry 
> > >straightforward.  Then I pulled the action, which did not 
> > slide out 
> > >easily, and saw the pinblock hanging 1/4" below the 
> > stretcher, and the 
> > >furrows ploughed (plowed?) by the drop screws.  OK, now we 
> > know why the 
> > >last guy didn't regulate the drop.  Obviously got to make 
> > some room to 
> > >raise the drop screws.  Shanks are original, so I might 
> > gain something by 
> > >bolstering knuckles, but probably not enough.  I could go 
> > in there with a 
> > >disk sander and grind some off the bottom of the pinblock, 
> > but I'd prefer 
> > >not to inflict the noise and mess on the customer's living 
> > room.  Anyone 
> > >else ever faced this situation, and found a neat (i.e. 
> > reasonably clean 
> > >and quiet) solution?
> > >
> > >thanks
> > >
> > >Mike Spalding, RPT
> > >
> > >_______________________________________________
> > >pianotech list info: https://www.moypiano.com/resources/#archives
> > >
> > >
> > >---
> > >Incoming mail is certified Virus Free.
> > >Checked by AVG anti-virus system (http://www.grisoft.com).
> > >Version: 6.0.386 / Virus Database: 218 - Release Date: 9/9/2002
> > 
> > Greg Newell
> > mailto:gnewell@ameritech.net
> > 
> _______________________________________________
> pianotech list info: https://www.moypiano.com/resources/#archives
> 


This PTG archive page provided courtesy of Moy Piano Service, LLC