Dyna2 stripper, more results

[Farrell]

Please expand on its use. After waiting the hour after application and then
scraping the yucko away, you are left with a bare veneer surface with a
little bit of drying stripper/finish mush. How do you do final cleaning of
the veneer? Do you wash it with water? How do you get the mush out of all
the grain? Thanks.

Terry Farrell
Piano Tuning & Service
Tampa, Florida
mfarrel2@tampabay.rr.com

----- Original Message -----
From: "gutlo" <gutlo@bestweb.net>
To: <pianotech@ptg.org>
Sent: Thursday, February 01, 2001 9:23 AM
Subject: Re: Dyna2 stripper, more results


----------
> From: Richard Oliver Snelson <rsnelson@dave-world.net>
> To: pianotech@ptg.org
> Subject: Re: Dyna2 stripper, more results
> Date: Wednesday, January 31, 2001 8:40 AM
>
> I stripped a case with Dyna2 yesterday and had good results. I had
> trouble at first in getting it to spread corrected but was told to  use
> a natural bristle brush, which worked fine. It did take a second
> application but that went very, very quickly. The clean up with water
> was even faster.
>
> I like: Excellent vertical holding, non toxic doesn't make my German
> Shepherd throw up like most other strippers do, removes at least 95% of
> the old piano finish the first pass. I also noticed that it doesn't
> bleach the wood. I like this since it allow better control. I've had
> other caustic strippers bleach heavily in some places and not in others.
>
>
>
> Richard
> Oliver Piano Services
>
> Greg Newell wrote:
> >
> > Dear list,
> >     I have finally tried the Dyna2 stripper I received. Since I
> > purchased a gallon I guess that my trial pint was given to someone
else.
> > I must say that I was rather unimpressed.
> >     Tonight I had some extra time (a rarity) and tried a patch slightly
> > larger than a square foot. I waited at least one hour as suggested and
> > scraped off part of the application. I found that several layers
> > remained on the test patch area and will have to be removed later. Not
> > long enough, right? I left the remainder for another hour or so and
then
> > tried to remove that. I found that it removed most of the old finish
but
> > was rather spotty in some areas. The part I tried was the large lid
> > standing on edge with it's long side on the floor. I will say that it
> > was great at not running anywhere (vertically applied). I would like it
> > to work a little better overall though.
> >     I will use this stuff for the case I'm sure since I would rather it
> > not drip anywhere but where I put it. I can count on this with Dyna2.
> > I'm sure though that it will take more than one application which I was
> > not prepared for. I guess I wrongly assumed that I would be done once I
> > waited long enough and all would scrape away. I'm thinking of using
this
> > for tender areas and the caustic stuff for the rest so I can hope to
> > finish the project while I still have life and breath in me. I'd be
> > interested to hear your results if you'd care to share. There should be
> > at least 8 of you out there who have access to this through your free
> > pints. Whatcha think?
> >
> > --
> > Greg Newell
> > Greg's Piano Forté
> > 19270 Harlon Ave.
> > Lakewood, Ohio 44107
> > 216-226-3791
> > mailto:gnewell@ameritech.net

Richard,

Glad to hear of your good results.  Greg will try again.

Thanks for your new order.

Arthur