Thanks Mark. I'm going to give it a whirl. Thanks tons for your input. Do you use and type of sealer on bare wood? Also, I have reverted back to my marine refinishing ways and applied an oil-based grain-filling paste stain to two mahogany test panels. My info is that if you let the oil-based stain dry thoroughly, you should be OK with compatability. I wonder though, if I should hit it with a sealer, or maybe something like a dewaxed shellac to be sure. Any thoughts? Obviously, if I don't have to, I would rather not use another product. Terry Farrell Piano Tuning & Service Tampa, Florida mfarrel2@tampabay.rr.com ----- Original Message ----- From: <bases-loaded@juno.com> To: <pianotech@ptg.org> Sent: Sunday, November 19, 2000 5:01 PM Subject: Re: Piano Finishes > Terry - > > I have used Target Coatings Premium Spray Lacquer (PSL) on my last 3 > grands. I can whole-heartedly endorse it as a great WB finish. In > particular, an ebony job I did using their products (black production WB > lacquer and 3-4 coats PSL clear gloss) is the best looking ebony job I > have ever done, with as litle fuss as you can expect on a job like that. > I rubbed to satin/semi, but am told that, unlike many WB finishes, the > PSL also rubs to gloss beautifully. I found it to be very user friendly, > sprays much like NC lacquer, levels well, dries quickly without the soft > belly, sands and rubs wonderfully well, and is superior to NC lacquer in > durability and mar and chemical resistance. And the 100% burn-in quality > is a real plus, and is not time sensitive. In other words, you do not > have to recoat within a certain window to keep the burn-in effective. > > They also have a finish that is very nice called Oxford Hybrid Varnish, > which is easily the warmest looking WB finish I have ever seen. Somehow > there is an emulsified tung oil in the finish that really warms the look > in a big way. There is a cross-linker available with this finish that > increases its durability considerably. I used it on an old upright and > it really had a nice heirloom or vintage look to it, similar in apearance > to an oil varnish, but is a WB and I sprayed it on. Very forgiving > finish and easy to use, but not appropriate when buffing to gloss. It > was probably the quickest route to a good looking finish that I have > experienced in a long time. > > I think Target Coatings is a quality supplier, and Jeff Weiss is always > willing to help out with any technical problems with his products. Jeff > Jewitt thinks highly of Target's products, too, and I have found his > opinions to be very trustworthy. In fact, last time I talked to him > (July 2000), he was completely phasing out his use of NC lacquer because > of how much he liked the PSL. > > That's high praise. > > Mark Potter > bases-loaded@juno.com > > > On Sun, 19 Nov 2000 10:48:16 -0500 "Farrell" <mfarrel2@tampabay.rr.com> > writes: > > Well, here I sit boxed into refinishing (or making ill-fated attempts > > to) a > > piano again. I am stuck on waterbase. I am eyeing OXFORD PREMIUM > > SPRAY > > LACQUER (1000 Series) water-base finish by Target Coatings. Has > > anyone tried > > it? Two features it claims attracts my interest: 100% burn in, so no > > "witness lines" when flat-sanding final coat and ease of > > flat-sanding/polishing - the big one being 100% burn-in. That is > > where I > > have had problems in the past. Anyone???????? > > > > I haven't even started yet, and the desperation & out-of-control > > feeling is > > already setting in :-(. > > > > Terry Farrell > > Piano Tuning & Service > > Tampa, Florida > > mfarrel2@tampabay.rr.com > > >
This PTG archive page provided courtesy of Moy Piano Service, LLC