[CAUT] hammer thickness trimming jig

[Greg Newell]

Shawn,

      I have the Spurlock jig of which you speak, I think. AS far as I can
tell it does NOT work with shanks installed. Is this the one you're talking
about?

 



 

Where would the shank go?

 

Greg Newell

Greg's Piano Forté

www.gregspianoforte.com

216-226-3791 (office)

216-470-8634 (mobile)

 

 

-----Original Message-----
From: caut-bounces at ptg.org [mailto:caut-bounces at ptg.org] On Behalf Of Shawn
Brock
Sent: Sunday, August 24, 2008 4:16 PM
To: Pianotech List
Cc: College and University Technicians
Subject: Re: [CAUT] hammer thickness trimming jig

 

Yes,

Spurlock does make a jig that does work nicely.  Its gotten me through some 

bad times before.  Like all Spurlock tools, it works wonderfully in my 

humble opinion.  I was shocked that no one had brought this up sooner in 

this discussion.  Guess most folks were sleeping in late like me...  Oh, and


you can use the Spurlock jig with hammers that are already installed on 

shanks, which is what is being asked.

 

Shawn Brock, RPT

----- Original Message ----- 

From: "Joe And Penny Goss" <imatunr at srvinet.com>

To: "Pianotech List" <pianotech at ptg.org>

Sent: Sunday, August 24, 2008 3:56 PM

Subject: Re: hammer thickness trimming jig

 

 

>I think Spurlock also has a jig similar to Rogers.

> Roger has two jigs one for the right the other for the left side.

> Joe Goss RPT

> Mother Goose Tools

> imatunr at srvinet.com

> www.mothergoosetools.com

> ----- Original Message ----- 

> From: "Greg Newell" <gnewell at ameritech.net>

> To: "'Pianotech List'" <pianotech at ptg.org>

> Sent: Sunday, August 24, 2008 10:49 AM

> Subject: RE: hammer thickness trimming jig

> 

> 

>> John,

>> The weight is fine. The thickness interferes with neighbors. Just

>> looking for the jig.

>> 

>> Greg Newell

>> Greg's Piano Forté

>> www.gregspianoforte.com

>> 216-226-3791 (office)

>> 216-470-8634 (mobile)

>> 

>> -----Original Message-----

>> From: pianotech-bounces at ptg.org [mailto:pianotech-bounces at ptg.org] On

> Behalf

>> Of John Delacour

>> Sent: Sunday, August 24, 2008 12:16 PM

>> To: Pianotech List; 'College and University Technicians'

>> Subject: Re: hammer thickness trimming jig

>> 

>> You've bought the wrong hammers, which are most likely to be too

>> heavy even if you find a way of planing them down to 10.5 or 11 mm

>> wide.  This would mean you'd end up with too heavy an action or too

>> sluggish an action owing to the lead you add to compensate for the

>> over-heavy hammers.  Can't you send them back and get the proper

>> lighter hammers for the early models?

>> 

>> JD

>> 

>> 

> 

> 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://www.moypiano.com/ptg/caut.php/attachments/20080824/b61badd2/attachment-0001.html 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/png
Size: 121056 bytes
Desc: not available
Url : https://www.moypiano.com/ptg/caut.php/attachments/20080824/b61badd2/attachment-0001.png